If you are in the process of starting a jewel line, there is a need to know how they are created so that you meet customer demands more effectively. Several methods are involved in making the final products. As long as the methods adhere to unique products are created, and this is what will bring customers to your shop. Below are steps involved in Tufa casting custom jewelry NM.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
Here comes the completion of work. There are multiple methods that one can choose to use in the final stages. At this point, one can create unique final products and other aspiration that might come to ones mind. It is important to note that the processes of sand cleaning and polishing can take a lot of time.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
Here comes the completion of work. There are multiple methods that one can choose to use in the final stages. At this point, one can create unique final products and other aspiration that might come to ones mind. It is important to note that the processes of sand cleaning and polishing can take a lot of time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.